Circuit Breaker Test Software BTS11 (English Only)

Used for SA10, SA10A, SA5, SA5A, DCM2, BTS2000, BTS2000A.

To install the program you must have administrator rights.

To make sure that you are an administrator on the computer, right-click the installation icon for the program, 
and then click Run as administrator. If you're prompted for an administrator password or confirmation, type the password or provide confirmation.

Note that "Use separate settings for all users" option will install database and settings files into 'My DocumentsBTS11' folder. Make sure that your 'My Documents Folder' is not stored on a network drive when using this option.

Microsoft Word is required for protocol printout.
Microsoft Excel is required for export to Excel.

Note! Microsoft Office Apps for Windows WILL NOT WORK!

This software has been tested to work on the following

Operating system

• Microsoft Windows 10 32-bits and 64-bits

• Microsoft Windows 11 32-bits and 64-bits

Microsoft Office desktop applications for PC

• Microsoft Office Version 2205 Build 16.0.15225.20348 32-bits and 64-bits

• Microsoft Office Version 2016 Build 16.0.4266.1001 32-bits and 64-bits

Version history

Version 1.6.0.2305 (English Only)

1. Fixed layout in database to resolve error saving switch type in BTS11 1.6.0.12
2. Fixed error creating database without any previous database open.
3. Some other minor bugs fixed.

Version 1.6.0.2304 (English Only)

1. Fixed bug that could make extra motor operation to not work on old SA5 and SA10 V4.31 and earlier.
2. Fixed a bug in loading of settings of contact filter that could cause wrong filter to be applied.
3. New coil armature time calculation that works n very small dips.
4. Fixed bug in display of some coil values.
5. Fixed in Setup measurement. Display of Angle curve only and use of conversion table is not possible to set anymore.
6. Added display of both contact and interval times.
7. Added check of invalid DCM curve view.
8. Added save of coil resistance on double and triple operation.
9. Added display of results for triple operation.
10. Some other minor bugs fixed.

Version 1.6.0.2300 (English Only)

1. Known issue in this version. Reference curve will not display correctly.
2. Improved layout and reduced number of rows in graph results.
3. Fixed bug that could result of time for previous contact was displayed if no contact time was found.
4. Added contact in calculation of Siemens image contact for double and triple operations.
5. Fixed errors in calculation of Siemens image contacts if disturbances occurred.
6. Fixed bug on trig of contact group 3 in sync operation.
7. Fixed bug that could occur in undo approved.
8. Added extra motor operation to DCM operations on SAxx Units.
9. Fixed bug saving counter values.
10. Fixed bug that could lose spring charge operation if acquisition time was too short.
11. Added error message to display if spring charge operation if acquisition time was too short.
12. Fixed cancelling of extra spring charge operation will display only main operation.
13. Added display of comments in Graph and Substation/Order
14. Fixed bugs in setup switch configuration
15. Fixed error could occur if exporting conversion table to file that contained illegal filename characters.
16. Added new firmware version 1.10 for DCM-CU
17. Added new firmware version 5.21 to SA10 Serial > 700 and SA10A. Version 5.20 should not be used.
18. Protocol printout Improved with option to generate document and send to printer at the same time.
19. Fixed bug that made printout fail sometimes.
20. Fixed Protocol printout missing image contact values.
21. Fixed Protocol printout missing Travel Time, Distance, and Speeds.
22. Fixed Protocol printout of motor times with motors on delay timer.
23. Fixed Protocol printout drawing of curves and other bugs when printing separate mechanism.
24. Added detection of switch position with Aux contacts for all operations. This can be disabled in software settings.
25. Fixed parameter sorting issues in database upgrade.
26. Fixed graph bugs.
27. Fixed missing variable declarations.
28. Fixed zero of current offset.
29. Several other minor bugs fixed.

Version 1.6.0.2239 (English Only)

1. Fixed errors in calculation of ABB image contacts if contacts was not adjusted correctly.
2. Fixed scale in graph if only contacts was viewed in DCM operation.
3. Fixed contact calculation in DCM close trip operation if trip was missing.
4. Fixed curve selection of DCM operation in graph.
5. Fixed coil resistance results were not always added to test object.
6. Fixed datapoints can be selected in drawing of filled contact curves.
7. Fixed bug that could prevent test object getting approved.
8. Fixed bug in gauge unit’s window.
9. Added POB power supply manual